Boat designed: George Buehler. Started deck beams on December 1,2004. Keel and deck beams went to the boat shed December, 2006. I have been working on this project for about 10 years and have not lost interest in it. My progress continues. I lost two years due to the storm Sandy. My progress on the boat far exceeds the posts on this site.I am going to post pictures showing progress. Bottom line is building is better than blogging.
Monday, July 9, 2012
Shed Frames
Once the foundation was completed I built my frames using 2" by 4". Side walls were 12' long and the rafters 16' and a 12' ceiling or collar ties all put together with plywood gussets to form a truss. I built them one on top of the other in three stacks spread out close to where they would be raised into position.
Starting the Boat Shed
As I mentioned in a previous post there was a delay in building the boat shed. Partly due to my work load in my business and also due to a n excavating contractor not showing up as promised. Once I had all the trees cleared I ran across an old friend Bob Bridger, who had just moved back to the area and he had a front end hoe. Bob is a local and was more than willing to do the required excavation and he even helped move the large old micro lam beams which Strober Lumber gave me as long as I paid the delivery charge. Although they were different sizes and dimensions they made a good foundation and partial wall onto which I will place the shed frames. Here Bobs hoisting one of the beams to the front wall area. As you can see the side foundations are complete and stand about 2’ high.
Tuesday, February 21, 2012
The Shaft Log
Since this boat has a motor it needs a shaft to move the propeller. The shaft in this design goes through the keel. That section of the keel is called the shaft log. I used two 3" by 8" clear Douglas-fir planks which will be hollowed out and put together. Sandwiched between the two, making the shaft alley, will be a Vernatube made of fiberglass which I purchased from Centek Industries. To hollow out the shaft alley I ran the each plank through the table saw working from the center, out and lowering the blade with each pass. Its easy if you do both pieces and both sides before you adjust the blade and move the fence. After the cutting I put a large key hole saw in the drill and ran it back and forth the length of the shaft alley making it smooth. Pictured is both parts of the shaft log coated with epoxy and the Vernatube in place just before they where clamped together. Note I have already drilled the keel bolts on both sides of the shaft alley. More on those buggers later.
The Keel the Backbone of the Boat
I decided to laminate my keel out of 2" by 8" Douglas-fir kiln dried wood as opposed to larger sections of wood or timbers. The wood was easily hand picked and I could cut out the bad sections if needed. Each piece was run through the planner to make a nice flat joint when put together. Both faces where covered with resorcinal glue clamped every 8 " or so and left to dry in the shop or basement which were kept at 70 degrees for the drying duration. This is a photo of the two main sections of the keel. I laminated each section separately but here they were stacked on top of each other for spacial reasons. Later as we will see these two parts will be tared together and bolted down. And by the way still no boat shed!
Tuesday, December 20, 2011
Beams and the beam jig
This shows the deck beams tightened down and waiting for the glue to set up. I used Titebond 2 glue. On the leftThis shows the deck beams tightened down and waiting for the glue to set up. I used Titebond 2 glue. On the left of the jig are the deck beams for the Stateroom and the beams forward of the Galley. The Pilot house and Galley beams, are being laminated on the other side of the beam jig. With this set up, I could laminate two beams a night. As George says its fun but it's a messy process. Waxed paper would be placed between the mold and the glued beam to prevent sticking to the mold. Once set the beam would br run through the planer till smooth and then a few coats of Tongue Oil
Sunday, December 11, 2011
The Deck Beams
Most people start the deck beams somewhere after the keel and in the middle of the frame construction. The deck beams where the first thing I built. My boat shed was not started, winter was approaching and I wanted to get started on the project. I could build the beams in my garage so it seemed logical to start with them, ( logical may be a word that should not be used when taking on a boat building project), but that's still up in the air in my mind! This is a picture of the jig I made to bend the 5/4" by 3" eastern red cedar. It consists of two 2"x12" cut to the specified crown glued together and mounted on a 2"x8" which will hold the rods I'm placing every 6" on both sides of the 2bys. Once the rods are in place I made 5" cap blocks out of old oak hardwood flooring which would set over the cedar planks to be laminated and eventually tightened down. More of this in the next post.
Friday, December 9, 2011
The plans
The first thing we did was to come up with a plan. My thoughts where it would be nice to have a movable home. A place where you could live and pick up and leave if you didn't like the spot you where at. Always liked the water and hate driving, so a boat was the obvious choice. We talked to Herb Smith, a world navigator up in Maine, who we go sailing with when we visit Boothbay Harbor. He asked a few questions of how we would like to travel on the water and then he recommended looking up George Beuhler and his Diesel Duck troller yachts designs on the internet. http://www.georgebuehler.com/ We did and fell in love with the whole concept and design of his boats.
After considering all the options we decided on a wooden 44' Diesel Duck troller. Wood because that's what I work with and by using standard lumber the cost would be lower than traditional wooden boat construction. This picture above is that of Marlene and Benno Klopfer 41' Diesel Duck who's travels and adventures can be followed on: http://www.sailblogs.com/member/dieselduck
After considering all the options we decided on a wooden 44' Diesel Duck troller. Wood because that's what I work with and by using standard lumber the cost would be lower than traditional wooden boat construction. This picture above is that of Marlene and Benno Klopfer 41' Diesel Duck who's travels and adventures can be followed on: http://www.sailblogs.com/member/dieselduck
Subscribe to:
Posts (Atom)






